Zie ook: Meet de draad van een draaibank (Lathe Spindle Thread)
This table is an attempt to assist in the selection of the correct headstock thread fitting to suit your lathe when you are choosing a chuck. Please note that you MUST check all available documentation shipped with your lathe and make any necessary measurements before committing to a particular size fitting. In most cases, exchanges can be made simply by returning the chuck mounting bush, avoiding excessive transport costs, but this is not always the case. Always test the bush on the headstock before fitting it to the lathe. Bushes can be difficult to remove once firmly fitted and damaged bushes cannot be replaced. If you’re not sure, send an e-mail first and we’ll try to advise. Note also that certain lathes are equipped with different mounting threads in different markets, whilst others have changed during the life of the lathe.
The sizes marked in RED are considered non-standard and some difficulty may be experienced in getting certain types/brands of equipment to suit: please enquire.
|
Imperial (inch) Headstock Threads |
|
Thread
|
Ref.
|
Lathes Using This Thread (but CHECK yours: threads may vary in different markets!!)
|
3/4″ x 16 tpi |
T01
|
All Record, all Coronet (except red Major); Sears Roebuck Craftsman; Klein; Carbatec; APTC KWL37; Nu-Tool NWL37; Naerok 12073; Clarke CWL12C; Draper WTL12A & WTL100; Rexon WL6V; Sealey SM42 |
3/4″ x 10 tpi |
T10
|
James Inns Sherwood range; Rockwell Homecraft; Naerok WL1000; Sealey. |
7/8″ x 16 tpi |
T08
|
Coronet Major (Maroon) |
1″ x 12 tpi |
T03
|
Myford ML8; Turnstyler |
1″ x 12 tpi |
T03HD
|
APTC H1000 |
1″ x 10 tpi |
T12
|
Harrison Jubilee; Arundel E5; Durden |
1″ x 8 tpi |
T04M
|
APTC M900, M950, M1000, M330, M600 & Perform CCL and CCBL; Wivamac (DB800, DB801, DB1000, DB1200, ADB950 – all models, US option); Sorby (some markets), Delta |
1.1/8″ 12 tpi |
T20
|
Myford ML7 |
1.1/8″ 12 tpi |
T20M
|
Myford Maestro (with lock screws) |
1.1/4″ x 8 tpi |
T23
|
Woodfast M Series (US models);VicMarc VL series (US models); Nova 3000 (US models); General 260 |
1.1/2″ x 8 tpi |
T39
|
|
1.1/2″ x 8 tpi |
T06
|
Powermatic |
1.1/2″ x 6 tpi |
T02
|
Axminster NV28-40; Harrison/Startrite/GLCo Graduate; Wadkin Bursgreen 6″ BL 150 Lungrens; Tanner FS100 some Woodfast models(!) |
1.1/2″ x 6 tpi |
T02P
|
Poolewood PW28-40 (Old type) |
5/8″ Plain Bore |
T05
|
Shopsmith; Multico Supershop |
|
|
Metric (metrisch) millimetre (millimeters) Headstock Threads |
|
Thread
|
Ref.
|
Lathes Using This Thread (but CHECK yours: threads may vary in different markets!!)
|
18 mm x 2.5 mm |
n/a
|
Elu only – enquire. |
20 mm x 1.5mm |
T33
|
Electro HDM800 & HDM1000; Multico, Poolewood |
20 mm x 2 mm |
T29
|
Tyme Cub (’83 on) & Little Gem |
24 mm x 3 mm |
T21
|
Luna; Arundel M230; Merlin K150/450/600 |
25 mm x 2 mm |
T30
|
Tyme Avon (’83 on) & Classic, Tanner SD165; Selbix Springwood; Sorby (some markets); Cotech |
30mm x 1.5mm |
T34
|
Alko HDM850 |
M30 x 3.5 mm |
T13
|
Woodfast C Series, Arundel M300 |
M30 x 3.5 mm |
T37
|
Teknatool; Nova 3000 & TL1500 (Europe); VicMarc VL100 (Europe); MiniMax T124 |
M33 x 3.5 mm |
T38
|
Wivamac (DB800, DB801, DB1000, DB1200, ADB950 – all models); Kity;Scheppach DMV200 & DMT180; Sorby (some markets); OneWay 2036/2436/2016/2416; Konig; Hager; Hegner; Flott BD180; Emco DB5, VicMarc VL200 & 300 (not US) |
M33 x 3.5 mm |
T38W
|
APTC Woodfast |
M33 x 3.5 mm |
T38H
|
Hapfo ONLY |
M33 x 3.5 mm |
T38V
|
VicMarc – special fitting |
M33 x 3.5 mm |
T38PRO
|
Axminster 4224 Professional |
|
|
Bayonet Headstock Mountings |
|
Thread
|
Ref.
|
Lathes Using This Mounting
|
Special Fitting |
VB36
|
VB Manufacturing (Hegner UK) VB36 |
|